Hi Jmozdzen,

Please find below your required information
"
linux-6fyq:~ # cat /etc/os-release
NAME="SLES"
VERSION="12-SP3"
VERSION_ID="12.3"
PRETTY_NAME="SUSE Linux Enterprise Server 12 SP3"
ID="sles"
ANSI_COLOR="0;32"
CPE_NAME="cpe:/o:suse:sles_sap:12:sp3"


[ 11.643363] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.689166] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 14.495327] igb 0000:05:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 14.599122] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.623313] igb 0000:06:00.0 eth1: igb: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 14.727075] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 14.739360] NET: Registered protocol family 17
[ 43.149149] pagecache limit set to 0.Feature is supported only for SLES for SAP appliance
[ 156.494555] fuse init (API version 7.23)
[ 755.684595] igb 0000:05:00.0 eth0: igb: eth0 NIC Link is Down
[ 801.767074] igb 0000:05:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 821.175577] igb 0000:06:00.0 eth1: igb: eth1 NIC Link is Down
[ 836.316626] igb 0000:06:00.0 eth1: igb: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX

linux-6fyq:~ # ip link list
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 0c:c4:7a:72:88:cc brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 0c:c4:7a:72:88:cd brd ff:ff:ff:ff:ff:ff

linux-6fyq:~ # ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes

linux-6fyq:~ # ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes

linux-6fyq:~ # ethtool -i eth0
driver: igb
version: 5.4.0-k
firmware-version: 3.16, 0x800004d7
expansion-rom-version:
bus-info: 0000:05:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no

linux-6fyq:~ # ethtool -i eth1
driver: igb
version: 5.4.0-k
firmware-version: 3.16, 0x800004d9
expansion-rom-version:
bus-info: 0000:06:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no
"

Waiting for your positive response & Best regards

Zaman