Results 1 to 9 of 9

Thread: Raspberry wifi setup issue

Hybrid View

  1. #1

    Post Raspberry wifi setup issue

    Hi Team,

    I am trying to setup wifi network for my raspberry pi.

    After this setup:
    hciattach /dev/ttyAMA0 bcm43xx 921600
    bcm43xx_init
    Flash firmware /lib/firmware/BCM43430A1.hcd
    Set Controller UART speed to 921600 bit/s
    Device setup complete

    After hciconfig hci0 up
    Hcitool scan shows scanning....

    doesn't show anything.

    Kindly suggest.

    cheers,
    Ashish

  2. #2

    Re: Raspberry wifi setup issue

    On 03/01/17 13:54, asodhi wrote:

    > I am trying to setup wifi network for my raspberry pi.
    >
    > After this setup:
    > hciattach /dev/ttyAMA0 bcm43xx 921600
    > bcm43xx_init
    > Flash firmware /lib/firmware/BCM43430A1.hcd
    > Set Controller UART speed to 921600 bit/s
    > Device setup complete
    >
    > After hciconfig hci0 up
    > Hcitool scan shows scanning....
    >
    > doesn't show anything.


    Since your first line enables the Bluetooth controller are you trying to
    set up a wireless (not wifi) network over Bluetooth?

    HTH.
    --
    Simon
    SUSE Knowledge Partner

    ------------------------------------------------------------------------
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below. Thanks.
    ------------------------------------------------------------------------

  3. #3

    Re: Raspberry wifi setup issue

    Hi Simon,

    Thanks for your reply.

    I am new to raspberry Pi.
    I am trying to setup my wireless network adapter to connect to wifi network.
    Please suggest

    cheers,
    Ashish

  4. Re: Raspberry wifi setup issue

    On Tue 03 Jan 2017 04:34:02 PM CST, asodhi wrote:

    Hi Simon,

    Thanks for your reply.

    I am new to raspberry Pi.
    I am trying to setup my wireless network adapter to connect to wifi
    network.
    Please suggest

    cheers,
    Ashish


    Hi
    Are you running the desktop, or just from the command line?

    If the desktop, there should be an icon on the panel to click and show
    network connections?

    Else if using wicked, rather than NetworkManager then this can be
    configure via the tool called YaST, then select System and then Network
    Settings, here you should see you wireless device and can edit it from
    here...











    Also note if not using dhcp, you do need to set the hostname/dns
    servers and also the default gateway. If not using ipv6, then suggest
    disabling from the 'global' tab.

    I use the command line and yast, in the desktop GUI it's called YaST2.

    --
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    openSUSE Leap 42.1|GNOME 3.16.2|4.1.36-44-default
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!


  5. #5

    Re: Raspberry wifi setup issue

    Hi Malcolm,

    I am using the desktop (GUI) and it is showing "network service disabled" and I am not able to see any option to choose the wireless networks there

    please suggest

  6. Re: Raspberry wifi setup issue

    Quote Originally Posted by asodhi View Post
    Hi Malcolm,

    I am using the desktop (GUI) and it is showing "network service disabled" and I am not able to see any option to choose the wireless networks there

    please suggest
    Hi
    So start up YaST and get to the network settings as indicated above, then in the 'Global' tab select the NetworkManager option as opposed to wicked service. I'm guessing in the first tab that opens you see both devices present?
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  7. #7

    Re: Raspberry wifi setup issue

    Hi Malcolm,

    Yes, I see both the devices in the network tab
    Screenshot 2017-01-05 17.14.40.png

    However in the GUI it only shows "Network service disabled" there is no icon to make this service enabled.

    I am able to connect to the network through wired connection but no icon to enable wifi

    Please suggest.

  8. Re: Raspberry wifi setup issue

    Hi
    So if you click onthe tab to the left of 'overview' Global Settings, is it wicked or Network Manager, if wicked, select Network Manager, save and check your settings again on the GUI.
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  9. Re: Raspberry wifi setup issue

    On Tue 03 Jan 2017 01:54:02 PM CST, asodhi wrote:

    Hi Team,

    I am trying to setup wifi network for my raspberry pi.

    After this setup:
    hciattach /dev/ttyAMA0 bcm43xx 921600
    bcm43xx_init
    Flash firmware /lib/firmware/BCM43430A1.hcd
    Set Controller UART speed to 921600 bit/s
    Device setup complete

    After hciconfig hci0 up
    Hcitool scan shows scanning....

    doesn't show anything.

    Kindly suggest.

    cheers,
    Ashish


    Hi
    The device your trying to connect to via bluetooth is discoverable?

    I tested here and works fine...

    Code:
    hciattach /dev/ttyAMA0 bcm43xx 921600
    bcm43xx_init
    Flash firmware /lib/firmware/BCM43430A1.hcd
    Set Controller UART speed to 921600 bit/s
    Device setup complete
    
    hciconfig hci0 up
    
    hciconfig
    hci0:	Type: BR/EDR  Bus: UART
    BD Address: XX:XX:XX:XX:XX:XX  ACL MTU: 1021:8  SCO MTU: 64:1
    UP RUNNING PSCAN
    RX bytes:1357 acl:0 sco:0 events:73 errors:0
    TX bytes:1185 acl:0 sco:0 commands:73 errors:0
    
    hcitool scan
    Scanning ...
    58:A2:XX:XX:XX:XX	LG Phone
    A0:02:XX:XX:XX:XX	Fire HD
    68:96:XX:XX:XX:XX	iPhone 5S
    --
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    openSUSE Leap 42.1|GNOME 3.16.2|4.1.36-41-default
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •