Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Wireless does not work

Hybrid View

  1. #1

    Unhappy Wireless does not work

    BCM4352 no wireless. What can I do? Thank you


    P: /devices/pci0000:00/0000:00:1c.3/0000:09:00.0
    E: DEVPATH=/devices/pci0000:00/0000:00:1c.3/0000:09:00.0
    E: DRIVER=bcma-pci-bridge
    E: ID_MODEL_FROM_DATABASE=BCM4352 802.11ac Wireless Network Adapter
    E: ID_PCI_CLASS_FROM_DATABASE=Network controller
    E: ID_PCI_SUBCLASS_FROM_DATABASE=Network controller
    E: ID_VENDOR_FROM_DATABASE=Broadcom Corporation
    E: MODALIAS=pci:v000014E4d000043B1sv000011ADsd0000660 6bc02sc80i00
    E: PCI_CLASS=28000
    E: PCI_ID=14E4:43B1
    E: PCI_SLOT_NAME=0000:09:00.0
    E: PCI_SUBSYS_ID=11AD:6606
    E: SUBSYSTEM=pci
    E: USEC_INITIALIZED=15892554

  2. Re: Wireless does not work

    Hi and welcome to the Forum
    What version of SLED? Please post the output from;
    Code:
    uname -a
    cat /etc/os-release
    If you run the command dmesg is there some clues (missing firmware) in the output?

    There is an option to use a third party package called broadcom-wl, but need to know the system info first.
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  3. #3

    Re: Wireless does not work

    Quote Originally Posted by malcolmlewis View Post
    Hi and welcome to the Forum
    What version of SLED? Please post the output from;
    Code:
    uname -a
    cat /etc/os-release
    If you run the command dmesg is there some clues (missing firmware) in the output?

    There is an option to use a third party package called broadcom-wl, but need to know the system info first.
    Linux laptop.suse 4.4.82-6.3-default #1 SMP Mon Aug 14 14:14:02 UTC 2017 (4c72484) x86_64 x86_64 x86_64 GNU/Linux


    NAME="SLED"
    VERSION="12-SP3"
    VERSION_ID="12.3"
    PRETTY_NAME="SUSE Linux Enterprise Desktop 12 SP3"
    ID="sled"
    ANSI_COLOR="0;32"
    CPE_NAME="cpe:/o:suse:sled:12:sp3"

  4. #4

    Re: Wireless does not work

    [ 3938.428826] [drm] PCIE GART of 3912M enabled (table at 0x0000000000040000).
    [ 3938.431393] cant't get the mac of 5
    [ 3938.439722] [ powerplay ] VBIOS did not find boot engine clock value in dependency table. Using Memory DPM level 0!
    [ 3938.439722] [drm] ring test on 0 succeeded in 11 usecs
    [ 3938.439921] [drm] ring test on 1 succeeded in 15 usecs
    [ 3938.439943] [drm] ring test on 2 succeeded in 11 usecs
    [ 3938.439950] [drm] ring test on 3 succeeded in 3 usecs
    [ 3938.439956] [drm] ring test on 4 succeeded in 2 usecs
    [ 3938.439961] [drm] ring test on 5 succeeded in 2 usecs
    [ 3938.439966] [drm] ring test on 6 succeeded in 2 usecs
    [ 3938.439971] [drm] ring test on 7 succeeded in 2 usecs
    [ 3938.439976] [drm] ring test on 8 succeeded in 2 usecs
    [ 3938.440008] [drm] ring test on 9 succeeded in 4 usecs
    [ 3938.440013] [drm] ring test on 10 succeeded in 4 usecs
    [ 3938.440048] [drm] ib test on ring 0 succeeded
    [ 3938.440135] [drm] ib test on ring 1 succeeded
    [ 3938.440161] [drm] ib test on ring 2 succeeded
    [ 3938.440180] [drm] ib test on ring 3 succeeded
    [ 3938.440199] [drm] ib test on ring 4 succeeded
    [ 3938.440217] [drm] ib test on ring 5 succeeded
    [ 3938.440236] [drm] ib test on ring 6 succeeded
    [ 3938.440256] [drm] ib test on ring 7 succeeded
    [ 3938.440306] [drm] ib test on ring 8 succeeded
    [ 3938.440323] [drm] ib test on ring 9 succeeded
    [ 3938.440336] [drm] ib test on ring 10 succeeded
    [ 3938.442177] r8169 0000:08:00.0 eth0: link down
    [ 3938.475771] xhci_hcd 0000:00:14.0: port 7 resume PLC timeout
    [ 3938.490931] xhci_hcd 0000:00:14.0: port 4 resume PLC timeout
    [ 3938.506078] xhci_hcd 0000:00:14.0: port 3 resume PLC timeout
    [ 3938.520531] pciehp 0000:00:1c.1cie04: Device 0000:07:00.0 already exists at 0000:07:00, cannot hot-add
    [ 3938.520532] pciehp 0000:00:1c.1cie04: Cannot add device at 0000:07:00
    [ 3938.731207] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 3938.732725] usb 1-4: reset full-speed USB device number 2 using xhci_hcd
    [ 3938.734821] ata1.00: configured for UDMA/133
    [ 3938.735283] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 3938.740161] ata2.00: configured for UDMA/100
    [ 3938.972776] usb 1-5: reset full-speed USB device number 3 using xhci_hcd
    [ 3939.360718] usb 1-8: reset low-speed USB device number 5 using xhci_hcd
    [ 3939.728757] rtc_cmos 00:02: System wakeup disabled by ACPI
    [ 3939.748757] usb 1-7: reset high-speed USB device number 4 using xhci_hcd
    [ 3939.925790] serio serio1: device_attach() failed for isa0060/serio1 (i8042 AUX0 port), error: -517
    [ 3939.925792] serio serio2: device_attach() failed for isa0060/serio2 (i8042 AUX1 port), error: -517
    [ 3939.932195] PM: resume of devices complete after 1515.281 msecs
    [ 3939.932247] usb 1-4:1.0: rebind failed: -517
    [ 3939.932249] usb 1-4:1.1: rebind failed: -517
    [ 3939.932415] PM: Finishing wakeup.
    [ 3939.932505] Restarting tasks ...
    [ 3939.932506] acpi PNP0501:00: Still not present
    [ 3939.932600] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
    [ 3939.933224] done.
    [ 3940.049647] usb 2-2: new SuperSpeed USB device number 2 using xhci_hcd
    [ 3940.065633] usb 2-2: New USB device found, idVendor=8564, idProduct=1000
    [ 3940.065637] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    [ 3940.065638] usb 2-2: Product: Mass Storage Device
    [ 3940.065639] usb 2-2: Manufacturer: JetFlash
    [ 3940.065641] usb 2-2: SerialNumber: 3034277972
    [ 3940.176511] r8169 0000:08:00.0 eth0: link up
    [ 3940.266231] r8169 0000:08:00.0 eth0: rtl_counters_cond == 1 (loop: 1000, delay: 10).
    [ 3940.292235] r8169 0000:08:00.0 eth0: rtl_counters_cond == 1 (loop: 1000, delay: 10).
    [ 3940.292462] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 3940.326643] r8169 0000:08:00.0 eth0: link down
    [ 3940.326690] r8169 0000:08:00.0 eth0: link down
    [ 3940.622708] psmouse serio3: synaptics: queried max coordinates: x [..5716], y [..4886]
    [ 3940.654914] psmouse serio3: synaptics: queried min coordinates: x [1220..], y [986..]
    [ 3941.892623] r8169 0000:08:00.0 eth0: link up
    [ 3941.921567] IPv4: martian source 255.255.255.255 from 192.168.0.36, on dev eth0
    [ 3941.921570] ll header: 00000000: ff ff ff ff ff ff 00 1e 67 d1 b4 54 08 00 ........g..T..
    [ 3945.064580] usb 2-2: Set SEL for device-initiated U1 failed.
    [ 3950.064713] usb 2-2: Set SEL for device-initiated U2 failed.
    [ 3950.070225] Bluetooth: hci0: BCM: chip id 63
    [ 3950.086113] Bluetooth: hci0: BCM20702A
    [ 3950.087109] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
    [ 3950.087130] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-04ca-200a.hcd failed with error -2
    [ 3950.087133] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-04ca-200a.hcd not found
    [ 3950.369936] usb-storage 2-2:1.0: USB Mass Storage device detected
    [ 3950.370020] scsi host4: usb-storage 2-2:1.0
    [ 3950.370117] usbcore: registered new interface driver usb-storage
    [ 3950.373219] usbcore: registered new interface driver uas
    [ 3951.369045] scsi 4:0:0:0: Direct-Access JetFlash Transcend 32GB 1.00 PQ: 0 ANSI: 6
    [ 3951.369323] sd 4:0:0:0: Attached scsi generic sg2 type 0
    [ 3951.369451] sd 4:0:0:0: [sdb] 61734912 512-byte logical blocks: (31.6 GB/29.4 GiB)
    [ 3951.369561] sd 4:0:0:0: [sdb] Write Protect is off
    [ 3951.369563] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00
    [ 3951.369691] sd 4:0:0:0: [sdb] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
    [ 3951.371093] sdb: sdb1
    [ 3951.371824] sd 4:0:0:0: [sdb] Attached SCSI removable disk
    [ 4054.697693] IPv4: martian source 255.255.255.255 from 192.168.0.36, on dev eth0
    [ 4054.697698] ll header: 00000000: ff ff ff ff ff ff 00 1e 67 d1 b4 54 08 00 ........g..T..
    [ 6855.981589] sdb: detected capacity change from 31608274944 to 0

  5. Re: Wireless does not work

    Hi
    Nothing in dmesg output?

    For the third party rpm, this needs to be built from the src rpm;
    http://packman.links2linux.org/packa...dcom-wl/817893

    As root user install;
    Code:
    kernel-default-devel kernel-syms make gcc rpmbuild
    As you user rebuild the package;
    Code:
    rpmbuild --rebuild broadcom-wl-6.30.223.271-7.3.src.rpm
    In the last 10 or so lines you will see the two rpm's needed down in the ~/rpmbuild/RPMS/x86_64 directory;

    As root user, change to the above directory, install and rebuild initrd;
    Code:
    su -
    cd /home/your_user/rpmbuild/RPMS/x86_64/
    zypper in broadcom-wl-6.30.223.271-7.3.x86_64.rpm broadcom-wl-kmp-default-6.30.223.271_k4.4.82_6.3-7.3.x86_64.rpm
    mkinitrd
    systemctl reboot
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  6. #6

    Cool Re: Wireless does not work

    Quote Originally Posted by malcolmlewis View Post
    Hi
    Nothing in dmesg output?

    For the third party rpm, this needs to be built from the src rpm;
    http://packman.links2linux.org/packa...dcom-wl/817893

    As root user install;
    Code:
    kernel-default-devel kernel-syms make gcc rpmbuild
    As you user rebuild the package;
    Code:
    rpmbuild --rebuild broadcom-wl-6.30.223.271-7.3.src.rpm
    In the last 10 or so lines you will see the two rpm's needed down in the ~/rpmbuild/RPMS/x86_64 directory;

    As root user, change to the above directory, install and rebuild initrd;
    Code:
    su -
    cd /home/your_user/rpmbuild/RPMS/x86_64/
    zypper in broadcom-wl-6.30.223.271-7.3.x86_64.rpm broadcom-wl-kmp-default-6.30.223.271_k4.4.82_6.3-7.3.x86_64.rpm
    mkinitrd
    systemctl reboot
    Thanks! That worked like a charm
    Last problem what about discrete graphics?

  7. Re: Wireless does not work

    Quote Originally Posted by sk8erbender View Post
    Thanks! That worked like a charm
    Last problem what about discrete graphics?
    Hi
    OK, one thing to note, after a kernel upgrade it will drop the wl module into weak-updates, so you will at some point need to rebuild/install the updated kmp again....

    What type of graphics, intel/nvidia? For this look at the bumblebee project...
    https://en.opensuse.org/SDB:NVIDIA_Bumblebee

    I don't see a SP3 repo yet...
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  8. #8

    Re: Wireless does not work

    Quote Originally Posted by malcolmlewis View Post
    Hi
    OK, one thing to note, after a kernel upgrade it will drop the wl module into weak-updates, so you will at some point need to rebuild/install the updated kmp again....

    What type of graphics, intel/nvidia? For this look at the bumblebee project...
    https://en.opensuse.org/SDB:NVIDIA_Bumblebee

    I don't see a SP3 repo yet...
    Radeon R5 M255

    and other one from cpu core i5-4210u

  9. Re: Wireless does not work

    Quote Originally Posted by sk8erbender View Post
    Radeon R5 M255

    and other one from cpu core i5-4210u
    Hi
    Can you disable the intel in the BIOS?

    Look at vgaswitcheroo?
    https://01.org/linuxgraphics/gfx-doc...witcheroo.html

    Does the system see the amdgpu or radeon driver?

    Code:
    /sbin/lspci -nnk |egrep -i -A3 "VGA|3D"
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  10. #10

    Smile Re: Wireless does not work

    Quote Originally Posted by malcolmlewis View Post
    Hi
    Can you disable the intel in the BIOS?

    Look at vgaswitcheroo?
    https://01.org/linuxgraphics/gfx-doc...witcheroo.html

    Does the system see the amdgpu or radeon driver?

    Code:
    /sbin/lspci -nnk |egrep -i -A3 "VGA|3D"
    /sbin/lspci -nnk |egrep -i -A3 "VGA|3D"
    00:02.0 VGA compatible controller [0300]: Intel Corporation Haswell-ULT Integrated Graphics Controller [8086:0a16] (rev 0b)
    Subsystem: Hewlett-Packard Company Device [103c:2249]
    Kernel driver in use: i915
    Kernel modules: i915

Page 1 of 2 12 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •